DIY Reindeer Antlers
Happy Spring Flower Bucket

Awards Show Watch Party!

Award show are upon us…are you having a watch party? Here’ some easy to make pieces that will jazz up your get together and personalize basic party décor. Go from boring to glamours!

Photo dec 18  4 08 19 pm

Brother sponsored post copy
Disclosure: Erin is a paid consultant and has received  products from Brother to evaluate. However, the opinions expressed are entirely her own and based on her use of the products.

This post contains affiliate links. If you buy from these links it won't cost you a penny more but Erin will make a little bit of money (not enough for a pony). 


Supplies:
ScanNCutDX Machine and Accessories
Foil Transfer Starter Kit
5 – 6” Tissue Paper Fan
1 Table Frame
1 Ready-Made Party Centerpiece
2 Black Cardstock
2 Gold Glitter Cardstock
2 Silver Glitter Cardstock
1 White Cardstock
Adhesive
Sewing Machine and Accessories
Printer
Washi Tape
Embellishments
Paper Trimmer or Scissors
FREE ScanNCut patterns:

FREE Printable:

 

N0te: Now I used my new ScanNCutDX machine to create all of these, but if you have an older model of ScanNCut you can use the cut files I created on that.

Instructions:
1. Download all the free patterns. To use them, either save them onto a USB drive and insert it into your ScanNCutDX or open them in CanvasWorkspace and use the ScanNCut Transfer feature to send it to your computer wirelessly.

20181217_173001
20181217_173001

2. Cut out the “party stars and circles” patterns from the free downloads by placing the gold cardstock onto the standard mat and insert it into the machine.
Load the “party stars and circles” pattern onto your ScanNCut following the instructions in step 1, then click on “ok” and then select “cut” and “start.”

20181217_142937

3. Cut out the “party circles” patterns from the free downloads by placing the gold cardstock onto the standard mat and insert it into the machine.
Load the “party circles” pattern onto your ScanNCut, following the instructions in step 1, then click on “ok” and then select “cut” and “start.” Repeat using 1 silver and 1 black piece of cardstock.

20181217_144749

4. Assemble the ready-made tissue paper fans and then adhere a large gold star to the center of each fan.

20181217_143149
20181217_143149

5. At your sewing machine, sew down the center of one of the circles, sew off the edge a few stitches and then threw another circle…repeating until you have a chain of circles.

20181217_170640

6. Cut out the “party foil centerpiece” pattern from the free downloads by placing the black cardstock onto the standard mat and insert it into the machine.
Load the pattern onto your ScanNCutDX and then select the scroll pattern and delete it.

20181217_173057

Then cut out the shape by clicking on “ok” and then select “cut” and “start.” Do not remove the cardstock once cut.


7. Open up the Foil Transfer Starter Kit. Place the glue pen into the holder and insert it into the machine.
Select “Foil1 (Glue),” follow the instructions on the screen and press start. Remove the glue pen and re-cap it.
Allow to dry.

20181217_172842

Select “Foil2 (Foil).” Follow the instructions on the screen. Place the pressing tool into the holder and insert it into the machine. Place the gold foil sheet, gold side up on top of the dried glue.

20181217_170847

Place the blue protective sheet over the foil and use Washi tape to hold it in place. Press start.
Once it’s finished unload the mat and remove the foil and protection sheet and brush off any gold debris.

Img_0826

8. Adhere it to the centerpiece.

Photo dec 18  3 13 57 pm

9. On your ScanNCutDX click on “patterns” then choose the words category.

Photo dec 18  3 09 18 pm
Photo dec 18  3 09 18 pm

Click on the word “party,” resize it to 3.5” wide and 1.04” high, and add it to the mat.

Photo dec 18  3 10 05 pm

Place a sheet of silver cardstock on the standard mat and cut it out.
10. Print the “party hashtag” printable on white cardstock.

Party hashtag

Place the printed paper onto the low tack mat and insert it into the machine.

20181218_162112

Load the “party hashtag” pattern onto your ScanNCutDX. Press the “scan” icon and “start” to scan in the page.

Click on “edit” then use the nudge arrows to line up the pattern with the scanned image.

20181217_164506

Use the Zoom icon to help enlarge the image in order to see it better.

20181217_164448

When it’s lined up, press “ok”
11. Select “Foil1 (Glue),” follow the instructions on the screen and press start. When finished, remove the glue pen and re-cap it.

20181217_153658

Allow to dry completely.
Select “Foil2 (Foil).” Follow the instructions on the screen. Place the pressing tool into the holder and insert it into the machine. Place the gold foil sheet, gold side up on top of the dried glue.

20181217_161406

Place the blue protective sheet over the foil and use Washi tape to hold it in place. Press start.

20181217_161435

Once it’s finished unload the mat and remove the foil and protection sheet and brush off any gold debris.

12. Trim down the party hashtag sign to 4” x 6” and insert it into the frame.

20181217_161853 (1)

Enjoy the party!

Photo dec 18  3 48 14 pm
Photo dec 18  3 48 14 pm
Photo dec 18  3 48 14 pm

Disclosure: Erin is a paid consultant and has received  products from Brother to evaluate. However, the opinions expressed are entirely her own and based on her use of the products.

This post contains affiliate links. If you buy from these links it won't cost you a penny more but Erin will make a little bit of money (not enough for a pony😉.)

ERIN Sig

Comments